Skip to content
AESTECHNO
AESTECHNO
Contact
Waves

Wavelength and frequency: λ = c/f and T = 1/f

A radio wave, or any signal travelling along a cable, repeats itself in time and in space. In time, one cycle lasts a period T; in space, one cycle stretches over a wavelength λ. The frequency f and the speed of the wave link the two.

Wavelength sets the length of an antenna, of a resonant stub and of a delay line, and tells when a trace on a board stops behaving like a simple wire. Inside a cable or a board the wave is slower than in vacuum, and the wavelength is shorter.

The formula

λ=cf,T=1f

Wavelength of an electromagnetic wave in vacuum, and period of a signal of frequency f.

Symbol Quantity Unit
λ Wavelength in vacuum metre (m)
c Speed of light in vacuum metre per second (m/s)
f Frequency hertz (Hz)
T Period second (s)
One wavelength is the distance between two crests (left). A quarter-wave antenna over a ground plane is about λ/4 long (right).

Period and frequency

A periodic signal repeats the same pattern again and again. The time one cycle takes is the period T, in seconds; the number of cycles per second is the frequency f, in hertz. Each one is the inverse of the other:

T=1f,f=1T

A 50 Hz mains voltage has a period of 20 ms, and a 1 GHz clock a period of 1 ns. The period is a duration, seen at one point in space. The wavelength is its counterpart in space: a distance, seen at one instant in time.

Where λ = c/f comes from

A wave travels at a speed v set by the medium it travels through. During one period, the whole pattern moves forward by exactly one wavelength, the distance between two crests. Speed is distance divided by time, so:

v=λT=λf

Solving for the wavelength gives λ=vf. In vacuum every electromagnetic wave travels at the speed of light c, which gives the formula at the top of the page. The speed of light is one of the defining constants of the SI, so its value is exact:

c=299 792 458m/s

In air the speed is only very slightly lower, so the same formula serves for radio waves in air. Rounding c to 3×108m/s makes every wavelength about 0.07 % too long, which is usually negligible. A handy form follows: the wavelength in metres is close to 300 divided by the frequency in megahertz. At 50 Hz the wavelength is close to 6000 km; at 2.4 GHz it is about 12.5 cm. Frequency and wavelength vary in opposite directions.

Velocity factor: the wavelength inside a cable

In a cable the wave does not travel through vacuum but through the insulation between the conductors. For a non-magnetic insulator its speed is divided by the square root of the relative permittivity εr of that dielectric. The ratio of this speed to c is the velocity factor VF:

VF=vc=1εr

Solid polyethylene, with εr close to 2.3, gives a velocity factor of about 0.66. Foamed dielectrics hold more air and reach about 0.8 or more. Typical coaxial and two-wire lines lie between 0.66 and 0.80. The frequency is set by the source and does not change, so the wavelength inside the line shrinks by the same factor. With λ0 the wavelength in vacuum:

λ=VF×cf=VF×λ0

This is the length that counts whenever a piece of cable is cut to a fraction of a wavelength, for a delay line, a resonant stub or an impedance transformer. The velocity factor of a given cable is published by its maker; use that value rather than a typical one.

Wavelength on a printed circuit board

A trace above a ground plane is a transmission line too. When the trace is buried between two planes (stripline), the whole field sits in the laminate and the effective permittivity equals the laminate's εr. When the trace runs on an outer layer (microstrip), part of the field is in the air above it, so the effective permittivity εeff is lower than εr, and the wave travels faster than in a stripline on the same board:

λ=cfεeff

On a laminate with εr=4, a stripline has a velocity factor of 14=0.5: the wavelength on the trace is half the wavelength in vacuum. A microstrip on the same board has a velocity factor between 0.5 and 1. Its exact value depends on the geometry of the trace and comes from a field solver or an impedance calculator.

Quarter-wave lengths: antennas and stubs

Many RF lengths are simple fractions of a wavelength. A half-wave dipole is two conductors whose total length is about λ2. A quarter-wave monopole is a single element above a ground plane: the plane acts as a mirror, and the element and its image behave like a dipole of twice the length. Its length is:

ℓ=λ4=c4f

In practice a resonant element is cut a few percent shorter than this, because of the end effect at its tip; the thicker the element compared with its length, the larger the correction. The usual approach is to cut it slightly long and trim it in small steps while measuring.

A quarter-wave section of cable or trace follows the same rule, with the wavelength inside the line: ℓ=VF×c4f. Such a section resonates and can transform an impedance, which is why it must be cut with the velocity factor of that line, not with the length in vacuum.

Worked example

A signal at 868 MHz: period, wavelength, quarter wave

A radio link works at 868 MHz. Find the period of the signal, its wavelength in air, the length of a quarter-wave antenna in air, and the length of a quarter-wave section of coaxial cable with a velocity factor of 0.66.

  1. Period: T=1868×106Hz≈1.152ns.
  2. Wavelength: λ=299 792 458m/s868×106Hz≈0.3454m, that is about 345.4 mm. The quick rule, 300 / 868, gives 345.6 mm.
  3. Quarter wave in air: λ4≈345.4mm4≈86.3mm. A real monopole element ends up a few percent shorter after trimming.
  4. Quarter wave in the cable: ℓ=0.66×86.35mm≈57.0mm.

Result: At 868 MHz the period is about 1.15 ns and the wavelength about 345 mm. A quarter wave is about 86 mm in air but only about 57 mm inside a cable with a velocity factor of 0.66.

Common mistakes

  • Dropping a unit prefix. The frequency must be in hertz for a result in metres: 868 MHz is 868×106Hz. The shortcut 300 / f works only with f in megahertz.
  • Using the wavelength in vacuum for a cable or a trace. Inside a line the wavelength is shorter by the velocity factor, so a stub cut to c4f is too long by about half in a cable with a velocity factor of 0.66.
  • Applying the cable's velocity factor to the antenna. The coaxial cable feeding an antenna does not change the length of the element radiating in air; only the dielectric around the element itself does.
  • Dividing by the permittivity instead of its square root. The velocity factor is 1εr: a dielectric with εr=4 halves the wavelength, it does not divide it by 4.
  • Taking the laminate's permittivity for a microstrip. Part of the field is in air, so the effective permittivity is lower than εr and the wavelength on an outer-layer trace is longer than on a buried one.
Calculator

Run the numbers with your own values:

A circuit to design?

Our design house in Montpellier, France designs and validates electronic boards, from schematic to production.

Our electronic design expertise

Frequently asked questions

How do you convert frequency to wavelength?
Divide the speed of light, 299 792 458 m/s, by the frequency in hertz. For radio work a quick version is: wavelength in metres is about 300 divided by the frequency in megahertz, so 100 MHz gives about 3 m and 2.4 GHz about 12.5 cm. Inside a cable or on a board, multiply the result by the velocity factor of the line.
What is the formula for the period of a wave?
The period is the inverse of the frequency, T = 1/f, with T in seconds and f in hertz. A 50 Hz signal has a period of 20 ms and a 1 GHz signal a period of 1 ns. The period also links wavelength and speed: the wave moves forward by one wavelength during one period.
What is the velocity factor of a cable?
It is the speed of a signal in the cable divided by the speed of light in vacuum. For a non-magnetic dielectric it equals one over the square root of the relative permittivity of the insulation. Solid polyethylene gives about 0.66, foamed dielectrics about 0.8 or more. The wavelength inside the cable is the wavelength in vacuum multiplied by this factor.
Why is a real quarter-wave antenna shorter than λ/4?
Because of the end effect at the tip of the element: the resonant length of a real conductor is a few percent shorter than a quarter of the wavelength in vacuum. The correction grows with the thickness of the element compared with its length. The usual practice is to cut the element slightly long and trim it in small steps while measuring.
Does the frequency change when a wave enters a cable?
No. The frequency is set by the source and stays the same along the whole path. What changes is the speed: the dielectric slows the wave down, so the wavelength shrinks in the same ratio. That is why a quarter-wave length of cable is shorter than a quarter wavelength in air at the same frequency.

Sources

Formulas and values checked against these published references.