LC resonant frequency: f0 = 1/(2π√LC)
An inductor and a capacitor connected together have one frequency at which their reactances are equal and cancel. At that resonant frequency the circuit behaves very differently from its behavior on either side of it.
Resonance is what tunes a radio, sets the frequency of an LC oscillator and shapes a filter. It is also why a decoupling capacitor stops acting as a capacitor above a certain frequency.
The formula
Resonant frequency of an ideal inductor L and capacitor C, in series or in parallel.
| Symbol | Quantity | Unit |
|---|---|---|
| Resonant frequency | hertz (Hz) | |
| Inductance | henry (H) | |
| Capacitance | farad (F) |
Two reactances that move in opposite directions
In AC, an inductor and a capacitor oppose the current with a reactance, measured in ohms. The reactance of the inductor grows with the frequency , while that of the capacitor falls with it:
Plot both against frequency and the two curves cross at a single point. In a series circuit, below it the capacitor's reactance dominates and the circuit is capacitive; above it the inductor's dominates and the circuit is inductive. A parallel tank is the other way round: inductive below the crossing, capacitive above. That crossing point is the resonant frequency .
Deriving the resonant frequency
Resonance is defined by . Write both reactances at the frequency :
Multiply both sides by the denominator on the right. The product of inductance and capacitance appears alone, and the angular resonant frequency follows:
Dividing by gives the formula at the top of the page, in hertz. As a check, 100 mH and 10 µF resonate at about 159 Hz. The resonant frequency depends on the product only, so doubling either value lowers it by a factor of .
Series resonance and parallel resonance
In a series RLC circuit the same current flows through all three parts, and the reactances add with opposite signs. The impedance, with the imaginary unit, is:
At the bracket is zero, so : the impedance is at its minimum, purely resistive, and the current at its maximum and in phase with the voltage. With an ideal inductor and capacitor and no resistance, the impedance of the series pair would fall to zero.
In a parallel LC tank the two branch currents are equal and opposite at resonance and cancel in the supply line. The tank then shows its maximum impedance, infinite in the ideal case, and draws almost no current, while a large current circulates between the inductor and the capacitor. Resistance in the inductor shifts the true peak slightly away from the ideal formula.
Energy swinging between L and C
In a lossless LC circuit the energy is never lost, it moves. When the capacitor is fully charged with the energy sits in its electric field; a quarter period later the current is at its peak and the same energy sits in the magnetic field of the inductor. At any instant the total is constant:
The energy goes back and forth twice per cycle of the current, so the energy stored in each component oscillates at , twice the resonant frequency. In a real circuit the resistance turns a little energy into heat at every swing, so the oscillation decays unless an amplifier makes up for the loss, which is exactly what an LC oscillator does.
Quality factor and bandwidth
The quality factor tells how sharp the resonance is. For a series RLC circuit it is the reactance of either component at resonance divided by the resistance; replacing by its value gives the second form:
The bandwidth is the range of frequencies over which the power stays above half its maximum. It is the resonant frequency divided by , which for the series circuit reduces to a simple ratio:
The term is the reactance of both components at resonance, often called the characteristic impedance. For a parallel circuit with the resistance placed in parallel, the expression is inverted: a larger parallel resistance gives a higher , so do not reuse the series formula there.
Where LC resonance shows up
Band-pass and band-stop filters use series and parallel resonators to pass or reject a band around f0. An LC oscillator uses a tank to set its frequency, and the tuning stage of a radio receiver adjusts a capacitor or an inductor to move its resonance onto the wanted station.
Matching networks use inductors and capacitors to cancel the reactance of a load, such as an antenna, at the operating frequency, so that the source sees a purely resistive load. This is the same cancellation of reactances that defines resonance.
Resonance also appears where nobody designed it. A real capacitor has an equivalent series inductance (ESL), so it is a series LC circuit with its own self-resonant frequency. Below it the part is capacitive, at it the impedance falls to the equivalent series resistance (ESR), and above it the part is inductive. Pads, vias and traces add to that inductance, and two capacitors of different values in parallel can form a parallel resonance, an impedance peak between their two self-resonant frequencies.
A series RLC circuit: resonance, Q and bandwidth
A 10 µH inductor, a 100 nF capacitor and a 1 Ω resistor are connected in series. Find the resonant frequency, the impedance of the circuit at resonance, the quality factor and the bandwidth.
- Convert to SI units: , .
- Compute the product and its square root: , .
- Apply the formula: .
- At that frequency each reactance has a magnitude of . They cancel, so only the resistance remains: .
- The quality factor is , and the bandwidth is , the same as R/(2πL).
Result: The circuit resonates near 159 kHz, where its impedance falls to 1 Ω; with Q = 10, the bandwidth is about 15.9 kHz.
Common mistakes
- Confusing angular frequency and frequency. is in radians per second; divide by to get hertz.
- Dropping a unit prefix. Picofarads and nanohenries must be converted to farads and henries before taking the square root; an error of 1000 in the product shifts the result by a factor of about 31.6.
- Assuming series and parallel resonance behave the same. Both occur at the same frequency, but a series circuit shows minimum impedance there and a parallel tank shows maximum impedance.
- Treating a decoupling capacitor as a capacitor at every frequency. Above its self-resonant frequency it is inductive, and a larger capacitance in the same package does not help there.
- Using the series formula for on a parallel circuit with a parallel resistor. In that case a larger resistance raises instead of lowering it.
Our design house in Montpellier, France designs and validates electronic boards, from schematic to production.
Frequently asked questions
- Why are the inductive and capacitive reactances equal at resonance?
- Because that is the definition of resonance. The inductive reactance grows with frequency and the capacitive reactance falls with it, so they meet at exactly one frequency. Setting 2π f L equal to 1 / (2π f C) and solving for f gives f0 = 1 / (2π √(LC)). At that frequency the two reactances cancel in a series circuit and the two branch currents cancel in a parallel one.
- What is the difference between series and parallel resonance?
- Both happen at the same frequency for the same L and C. A series LC circuit has its minimum impedance at resonance, equal to its resistance, so it passes a large current. A parallel LC tank has its maximum impedance at resonance and draws little current from the source, while a large current circulates between the inductor and the capacitor.
- How do you calculate the Q factor of a series RLC circuit?
- Divide the reactance of the inductor at resonance by the series resistance: Q = 2π f0 L / R. Replacing f0 by its value gives Q = (1/R) √(L/C). The bandwidth between the half-power points is then f0 / Q, which for the series circuit equals R / (2π L) in hertz. A higher Q means a narrower, sharper resonance.
- What is the self-resonant frequency of a capacitor?
- It is the frequency at which the capacitance resonates with the capacitor's own equivalent series inductance, ESL. The formula is the same LC formula, with ESL in place of L. At that frequency the impedance falls to the equivalent series resistance; above it the capacitor behaves as an inductor, which limits how high in frequency a decoupling capacitor is effective.
- Does resistance change the resonant frequency of an LC circuit?
- In a series RLC circuit the frequency of minimum impedance stays at 1 / (2π √(LC)); the resistance only sets the height and width of the peak. In a parallel tank whose inductor has a series resistance, the impedance peak moves slightly away from that value, and with enough resistance the circuit stops resonating clearly.
Sources
- OpenStax, University Physics Volume 2, 15.5 Resonance in an AC Circuit
- HyperPhysics (Georgia State University), Series RLC Resonance
- All About Circuits, Lessons in Electric Circuits Vol. II, Simple Parallel (Tank Circuit) Resonance
- Murata, EMI suppression filters basics, chapter 6: capacitor ESL, ESR and self-resonance
Formulas and values checked against these published references.