Current divider formula: I1 = I·R2/(R1+R2)
When a current reaches two resistors in parallel, it splits between them. The current in is the total current times the opposite resistor , divided by the sum of the two resistances.
The smaller resistor always takes the larger share. The same rule sets the range of an ammeter shunt and explains why parts placed in parallel never share a current perfectly.
The formula
Current in R1 when a total current I splits between two resistors R1 and R2 in parallel.
| Symbol | Quantity | Unit |
|---|---|---|
| Current through R1 | ampere (A) | |
| Total current entering the parallel pair | ampere (A) | |
| Resistance of the branch being calculated | ohm (Ω) | |
| Resistance of the other branch | ohm (Ω) |
Where the formula comes from
Two resistors in parallel are connected to the same pair of nodes, so they have the same voltage across them. Ohm's law applied to each branch gives:
Charge is conserved at the top node: the current that enters it leaves through the two branches. Writing each branch current as divided by its resistance gives the common voltage in terms of :
The second expression is times the equivalent resistance of the pair. Dividing it by , then by , gives each branch current:
Why the smaller resistor takes the larger current
Both branches see the same voltage, so each one draws a current inversely proportional to its resistance. Dividing one branch current by the other makes this explicit:
This is why the opposite resistor appears in the numerator. If is large, little current goes that way and almost all of flows through . If the two resistances are equal, each branch carries half. A resistor twice as large carries half the current of the other one.
The conductance form for any number of branches
The two-resistor formula does not extend directly to three or more branches. The clean general form uses conductance, the inverse of resistance, measured in siemens (S):
With branches in parallel, each branch current is the total current times that branch's conductance, divided by the sum of all the conductances:
Here the branch's own term is on top, because a larger conductance means a smaller resistance. For two branches, replacing each conductance by one over its resistance gives back .
Current shunts and sharing between parallel parts
A moving-coil meter of resistance becomes an ammeter for larger currents when a small shunt resistance is placed in parallel with it. Only the fraction given by the divider rule goes through the meter:
Parts placed in parallel to share a current follow the same rule, so equal nominal values are not enough. Two resistors at opposite ends of a tolerance band differ by about 2 %, and each one then carries about 1 % more or less than half of .
The connections count too, because they sit in series with each branch. With two resistors in parallel, of extra copper in one branch raises it to : the other branch now takes , about 52 %, and the longer path only . Parts whose resistance is not constant, such as diodes, are usually given a small series resistor each so that a known value dominates every branch.
90 mA into 100 Ω and 200 Ω in parallel
A current of 90 mA enters a 100 Ω resistor in parallel with a 200 Ω resistor. How much current flows through each resistor, and what voltage appears across them?
- Write down the data: , , . R1 is the smaller resistor, so it should take the larger current.
- Apply the formula, with the opposite resistor R2 in the numerator: .
- The rest goes through R2: . Check with Ohm's law, since both branches see the same voltage: .
Result: 60 mA through the 100 Ω resistor, 30 mA through the 200 Ω resistor, and 6 V across both.
Common mistakes
- Putting the resistor of the branch itself in the numerator. That is the voltage divider formula; for current, the opposite resistor goes on top: .
- Using the two-resistor formula with three or more branches. Use the conductance form, or the total current times the equivalent resistance divided by the branch resistance.
- Summing resistances in the denominator of the general form. For N branches the denominator is the sum of the conductances, not of the resistances.
- Expecting identical nominal parts to share exactly half each. Tolerance and the resistance of the connections in each branch shift the split.
- Applying the formula to parts whose resistance changes with current or temperature, such as diodes, without a series resistor in each branch to set the sharing.
Our design house in Montpellier, France designs and validates electronic boards, from schematic to production.
Frequently asked questions
- What is the current divider formula for two resistors?
- The current in one resistor equals the total current times the other resistor, divided by the sum of both resistances: I1 = I × R2 / (R1 + R2). The current in the second resistor is I × R1 / (R1 + R2), and the two branch currents add up to the total current I.
- Why is the opposite resistor in the numerator?
- Because both resistors see the same voltage, so each branch current is inversely proportional to its own resistance. A large R2 pushes most of the current into R1, which is exactly what R2 in the numerator of the formula for I1 expresses. Equal resistors split the current in half.
- How do you split current between three or more resistors?
- Use conductances, G = 1/R. Each branch current is the total current times the conductance of that branch, divided by the sum of all the branch conductances. An equivalent method is to multiply the total current by the equivalent resistance of the parallel group and divide by the branch resistance.
- What is the difference between a current divider and a voltage divider?
- A voltage divider is two resistors in series carrying the same current, and the voltage splits in proportion to each resistance. A current divider is two resistors in parallel at the same voltage, and the current splits in inverse proportion to each resistance. That is why the voltage formula has the resistor's own value in the numerator, and the current formula has the other resistor's value.
- Do identical resistors in parallel share current equally?
- Only if they are truly identical, connections included. Real resistors have a tolerance, and the copper, solder and connectors in each branch add resistance in series. Each difference shifts the split according to the divider rule, so in practice the sharing is close to equal but never exact.
Sources
- OpenStax, University Physics Volume 2, 10.2 Resistors in Series and Parallel
- Electronics Tutorials, Current Divider and the Current Divider Rule
- All About Circuits, Lessons in Electric Circuits Vol. I, Current Divider Circuits
- OpenStax, College Physics 2e, 21.4 DC Voltmeters and Ammeters
Formulas and values checked against these published references.